Chlorinated Rubber Paint

A general purpose very hard-wearing chemically resistant paint with excellent chemical and abrasion resistance. Ideal where conditions require a degree of chemical and water resistance typical...

A general purpose very hard-wearing chemically resistant paint with excellent chemical and abrasion resistance. Ideal where conditions require a degree of chemical and water resistance typical examples would be dairy parlours, catteries, kennels, road crossings, swimming pools, manhole covers, metal or concrete posts and metal tanks. It is also excellent for road markings where high visibility and durability is a must. Chlorinated Rubber paint should not be applied over PVA sealer, latex self levelling compounds or power floated concrete (see below). 

Area of use:

Interior and exterior

Substrates:

Concrete, ferrous metal, manhole covers and road surfaces

Packing:

5 litres

Physical Constants:

Colours: Yellow 10E53 and White (other colours on request min batch 150L)
Finish: Semi gloss
Volume solids: 55%
Theoretical spreading rate: 15 m2 per litre
Typical spreading rate 10 - 12m2 per litre dependent on surface porosity
Flash point: 23°C
Specific gravity: 1.3 - 1.4
Dry to touch: 1 - 2 hours (20°C)
Over-coating time: 16 hours
*The theoretical spreading rate has been calculated for the stated volume solids and dry film thickness. A practical spreading rate will depend on the actual dry film thickness, the nature of the substrate, and the relevant consumption factor. The physical constants are subject to normal manufacturing tolerances.

 

 PU-Black-150.jpg PU-Yellow-150.jpg PU-White-150.jpg 


Application Details:

Application method: Brush, roller, conventional and airless spray
Thinner: Xylene
Cleaning of tools: Xylene
Number of coats: 1 - 2 depending on the substrate and finish required. (Do not apply too thickly)

Preparation:

The surface should be stable, firm, dry and free of dust, sand, loose old paint, dirt, grease and oil. Existing smooth surfaces should be lightly abraded and cleaned first. Do not apply at temperatures below 5oC. When applying to absorbent surface such as trowel finished concrete adhesion will be improved by diluting the first coat by 10% with Xylene. Powerfloated concrete should be etched or mechanically abraded before application. Chlorinated rubber does not require priming but for the best results we recommend using a rust inhibiting primer on ferrous metals. There can be a solvent reaction with some substrates. When applying to large areas (more than 20m2) or if there is any doubt over adhesion or solvent reaction always apply to a small test area first. Nb. Chlorinated rubber paint is not suitable for overcoating with a conventional paint. 

more
Showing 1 - 2 of 2 items

Catalog

Enabled filters:
    By Brand
    Showing 1 - 2 of 2 items

    Chlorinated Rubber Paint

    A general purpose very hard-wearing chemically resistant paint with excellent chemical and abrasion resistance. Ideal where conditions require a degree of chemical and water resistance typical examples would be dairy parlours, catteries, kennels, road crossings, swimming pools, manhole covers, metal or concrete posts and metal tanks. It is also excellent for road markings where high visibility and durability is a must. Chlorinated Rubber paint should not be applied over PVA sealer, latex self levelling compounds or power floated concrete (see below). 

    Area of use:

    Interior and exterior

    Substrates:

    Concrete, ferrous metal, manhole covers and road surfaces

    Packing:

    5 litres

    Physical Constants:

    Colours: Yellow 10E53 and White (other colours on request min batch 150L)
    Finish: Semi gloss
    Volume solids: 55%
    Theoretical spreading rate: 15 m2 per litre
    Typical spreading rate 10 - 12m2 per litre dependent on surface porosity
    Flash point: 23°C
    Specific gravity: 1.3 - 1.4
    Dry to touch: 1 - 2 hours (20°C)
    Over-coating time: 16 hours
    *The theoretical spreading rate has been calculated for the stated volume solids and dry film thickness. A practical spreading rate will depend on the actual dry film thickness, the nature of the substrate, and the relevant consumption factor. The physical constants are subject to normal manufacturing tolerances.

     

     PU-Black-150.jpg PU-Yellow-150.jpg PU-White-150.jpg 


    Application Details:

    Application method: Brush, roller, conventional and airless spray
    Thinner: Xylene
    Cleaning of tools: Xylene
    Number of coats: 1 - 2 depending on the substrate and finish required. (Do not apply too thickly)

    Preparation:

    The surface should be stable, firm, dry and free of dust, sand, loose old paint, dirt, grease and oil. Existing smooth surfaces should be lightly abraded and cleaned first. Do not apply at temperatures below 5oC. When applying to absorbent surface such as trowel finished concrete adhesion will be improved by diluting the first coat by 10% with Xylene. Powerfloated concrete should be etched or mechanically abraded before application. Chlorinated rubber does not require priming but for the best results we recommend using a rust inhibiting primer on ferrous metals. There can be a solvent reaction with some substrates. When applying to large areas (more than 20m2) or if there is any doubt over adhesion or solvent reaction always apply to a small test area first. Nb. Chlorinated rubber paint is not suitable for overcoating with a conventional paint. 

    01235 427000

    Open Today 9am-5:30pm